dc53 tool steel

DC-53 Tool Steel | Alro Steel

DC53, is an improvement over alloy tool steel D-2. It eliminates the disadvantages of insufficient hardness and toughness that are a result of high-temperature tempering found with D-2. DC-53 is typically chosen as a replacement for D-2 in use for general purpose and precision dies.

Cold Work Die Steels: DC53 - Mold Steel

Cold Work Die Steels. DC53. DC53 is a general purpose cold work tool steel with exceptional Toughness, Wear Resistance, Compressive Strength and Temper Resistance.[PDF]

Medium Chrome Tool Steel DC53 Features - Alro Steel

DC53 and have experienced an increase in tool life by a factor of three compared to traditional draw tooling.” “With DC53 we are able to offer our customer’s a better performing steel while decreasing our

DC53 Tool Steel - Special steel china supplier-OTAI ...

DC53 Form of Supply. For Cold work tool steel DC53, we can supply the steel round bar, steel flat bar, steel sheet, plate and square block. DC53 tool steel round …

DC53 STEEL - titus steel

Tool steels such as S7, A2, and D2 typically do not meet this requirement. DC53 however, when tempered at or above 540°C (1,000°F) is not affected by these processes and will maintain original size and heat treat characteristics.Location: 6767 Invader Crescent, Mississauga, L5T 2B7, ON[PDF]

DC53Brochure08LSi - Lindquist Steels, Inc.

DC53 is a general purpose cold work tool steel with exceptional Toughness, Wear Resistance, Compressive Strength and Temper Resistance. These properties are obtained through its

Dc53 Tool Steel, Dc53 Tool Steel Suppliers and ...

Alibaba offers 1,489 dc53 tool steel products. About 8% of these are steel round bars, 2% are steel sheets, and 2% are flat steel. A wide variety of dc53 tool steel options are available to you, such as aisi, astm, and gb.

Dc53 ? | BladeForums

bladeforums› …› General Knife Maker's DiscussionJan 25, 2006· DC53, is an improvement over the alloy tool steel SKD11 specified in Japanese Industrial Standard (JIS) G4404. It eliminates the disadvantage of insufficient hardness and toughness, resulting from high-temperature tempering found with SKD11, and is intended to replace SKD11 in use for general purposes and precision dies.Natrix Copper | BladeForumsMar 11, 2018Why don't we see more DC53 blades? | BladeForumsMar 10, 2018Anybody out there tried S5 or S7 steel??? | BladeForumsAug 22, 2013steel craze: D2 vs M2 (and M4) | BladeForumsOct 07, 2005See more results[PDF]

DC53Brochure08LSi - Lindquist Steels, Inc.

DC53 is a general purpose cold work tool steel with exceptional Toughness, Wear Resistance, Compressive Strength and Temper Resistance. These properties are obtained through its

DC53 TOOL STEEL - Hot Work - Bladesmith's Forum Board

Apr 16, 2006· DC53 and D2 require the same austenitizing temperatures (1,020 – 1,040°C) and can be heat-treated at the same time. High temperature tempering (520°C or higher) allows DC53 to retain its high hardness and wire electro-discharge machinability.

Dc53 Tool Steel, Dc53 Tool Steel Suppliers and ...

Alibaba offers 1,489 dc53 tool steel products. About 8% of these are steel round bars, 2% are steel sheets, and 2% are flat steel. A wide variety of dc53 tool steel options are available to you, such as aisi, astm, and gb.

DC53 Steel - Fushun Special Steel

DC53 steel, is an improvement over alloy tool steel D2 specified in Standard (JIS) G4404. It eliminates the disadvantages of insufficient hardness and toughness, resulting from high-temperature tempering found with D2, and is intended to replace D2 in use for general purpose and precision dies.

DC53 - steel-grades

Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. DC53 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.

Misumi DC53 JIS Tool Steel - MatWeb

JIS Tool Steel, General purpose cold work die and mold steel whose strength and toughness approach those of high speed steels. Good machinability and grindability. Tougher than D2 Tool Steel. Machines 30% faster than D2 and A2. About the same

Cold Work Die Steels: DC53 - Fabrication Characteristics

DC53 can typically be machined 20% to 40% faster than D2 while experiencing as much as 50% less tool wear and breakdown. Faster feeds and speeds reduce …

DC-53 Tool Steel - myalro

DC53, is an improvement over alloy tool steel D-2. It eliminates the disadvantages of insufficient hardness and toughness that are a result of high-temperature tempering found with D-2. DC-53 is typically chosen as a replacement for D-2 in use for general purpose and precision dies.

Dc53 ? | BladeForums

bladeforums› …› General Knife Maker's DiscussionJan 25, 2006· DC53, is an improvement over the alloy tool steel SKD11 specified in Japanese Industrial Standard (JIS) G4404. It eliminates the disadvantage of insufficient hardness and toughness, resulting from high-temperature tempering found with SKD11, and is intended to replace SKD11 in use for general purposes and precision dies.[PDF]

Room - 大同特殊鋼

Our newly developed cold die steel, DC53, is an improvement over the alloy tool steel SKD11 specified in Japanese Industrial Standard (JIS) G4404. It eliminates the disadvantage of insufficient hardness and toughness, resulting from high-temperature[PDF]

DC53 & Surface Treatments - imsteel

DC53 & Surface Treatments International Mold Steel • 6796 Powerline Dr, Florence, KY 41042 • (800) 625-6653 Web – imsteel Conclusion - Tools should be finished to size and polished prior to applying the surface treatment.

Cold Work Tool Steel - Special steel china supplier-OTAI ...

This group of cold work tool steel is commonly used for drawing dies, die-casting die blocks and forging dies. D2 Tool Steel. D2 Tool Steel is a high carbon – high chromium air hardening tool steel, heat treatable to 60-62 Rc. ... DC53 Tool Steel is a general purpose cold work tool steel. Take a closer look. SKD11 Tool Steel.[PDF]

DC53 Heat Treat - Welcome to International Mold Steel

DC53 Heat Treat International Mold Steel • 6796 Powerline Dr, Florence, KY 41042 • (800) 625-6653 Web – imsteel Inspection - Conducting a hardness test after the heat treat process is complete is just one method used to measure the quality of heat treat.

DC53 cold work die Steels | Gloria Steel

Primary carbides in DC53 are relatively small with highly uniform distribution as compared to other tool steel grades such as D2 or SKD11. This helps to provide DC53 …

Hot Products

We are here to serve you!

Reply to technical consultation Provide design solution Dispatch engineers domestically/abroad Handle complaints thoroughly Systematic training Trouble judgment &amo; removal